ISO Standards Testing Equipment

AUTOCLAVE C6 (Gabbrielli) A Gabbrielli autoclave. Ceramic testing equipment for the determination of the crazing resistance of the glazed tiles and tableware. Stainless steel container diameter 560 mm height: 650 mm. According the Standards EN105 and ISO 10545-11.

Further Information About " Autoclave C6 (Craze Testing)for ceramic testing to ISO 10545-11"

This Gabbrielli Deep Abrasion Tester is for the determination of the resistance to abrasion of the unglazed ceramic tiles according to the ceramic test Standards EN 102 and ISO 10545-6

Further Information About " Deep Abrasion Testers (Gabbrielli) for ceramics testing to ISO 10545-6"

A Gabbrielli ceramic testing instrument to execute the water absorption on the ceramic tiles using the method of the sample water impregnation in immersion under vacuum. Container dimensions: 300x750x760 mm.

Further Information About " Deprimometer Water Absorption Apparatus for ceramics testing to ISO 10545-12 (Gabbrielli)"

C04292 - Surface Abrasion Tester W3B WITH 3 STATIONS This Gabbrielli ceramics test equipment to determine the abrasion resistance of glazed ceramic tiles according to the Standards EN 154 and ISO 10545-7.

Further Information About " Surface Abrasion Tester (Gabbrielli) for Ceramics Testing to ISO 10545-7"

The Wessex Pendulum Skid Tester is used in many applications to test the slip resistance of wet and dry surfaces, both at the design stage and also in the investigation of accidents. According the Standards BS 812 Pt 114 and EN 1097-8. It meets with the requirements of ISO10545

Further Information About " Wessex Pendulum Skid Tester ISO10545"

ATOMIC ABSORPTION SPECTROMETER

Further Information About "Atomic Absorption Systems"

C02382 - AUTOCLAVE C7 A Gabbrielli instrument for ceramic testing of the determination of the crazing resistance of the glazed tiles and tableware. Stainless steel container diameter: 300 mm height: 330 mm. According the Standards EN 105 and ISO 10545-11

Further Information About "Autoclave (Craze Testing) for ceramics testing to ISO10545-11"

2000 SERIES

Further Information About "Digital Thermometers"

The Glaze Thickness Penetrometer has been designed to offer a quick and easy way to measure the thickness of unfired glaze on ceramic surfaces. Two models are offered

Further Information About "Glaze Thickness Measurement"

The 456GT ultrasonic glaze thickness measuring instrument is best suited to situations where automatic spray systems are in place.

Further Information About "Glaze Thickness Measurement (Ultrasonic)"

A multi-chamber kiln that offers 9 chambers which can have temperature and profiles independently set making it ideal for ceramic testing. The gradient kiln offers a quick method of testing a single product at different temperatures or variety of products at the same temperature or a combination of both

Further Information About "Gradient Kiln 1300 C & 1400 C for ceramic testing"

The Harrow Ceramic Glaze Thickness Measurement Instrument was designed to offer a quick pass or fail method to test both flat and curved surfaces. It offers a simple method where an exact thickness is not generally required. The instrument can indicate if there is enough or too much or too little glaze applied

Further Information About "Harrow Glaze Thickness Measurement Instrument"

The latest development in High Shear Laboratory mixing — the new Silverson L5 Series — is ideal for all laboratory work, research and development, QA analysis and small scale production in all industries.

Further Information About "High Shear Mixers - Homogenisers - Stirrers"

Climatic chamber for determining resistance to frost to the ceramic testing standard ISO 10545-12

Further Information About "ISO 10545-12 Climatic Chamber for testing resistance to frost"

A Gabbrielli ceramic testing instrument, the precision Datapluctometro or universal gauge is suitable for measuring tiles or other objects in a continuous or programmed mode . Supplied with software for the acquisition/recording and data calculation. By using the ISO 10545-2 software, supplied with the instrument, measurements of length of the sides, the orthogonality of the adjacent sides and the parallelism of the opposite sides, the concavity and convexity, the warping and the curvature/bending of the sides of ceramic tiles according the Standard EN98 and ISO 10545-2. Using the software HD4, optional, besides to see and to acquire the initial measure compared to the sample, it records all the subsequent variations that the object could have in the time.

Further Information About "ISO 10545-2 Dimensions Testing Dataplucometro for ceramic tiles (Gabbrielli)"

The Crab 424 is a fully automatic precision Modulus of Rupture machine for the measurement of the breaking force and flexural tensile strength of the ceramic tiles according the ceramic testing Standard EN100 and ISO 10545-4.

Further Information About "ISO 10545-4 Strength Tester - Modulus of Rupture - MOR (Gabbrielli)"

A Gabbrielli Pullmeter to measure the static coefficient of friction of surfaces according the ceramics testing standard ASTM C 1028 and ISO 10545-5 annex B (not approved)

Further Information About "ISO 10545-5 Slipperiness Tester PULLMETER Static Coefficient of Friction Tester"

Precision reference plates to set to zero the instruments for the dimensional measurement equipment (Dataplucometro) manufactured by Gabbrielli for the ceramic testing standard ISO10545-2

Further Information About "ISO10545-2 Calibration Plates for Dataplucometro Dimensional Apparatus"

Precision Gabbrielli ceramic test equipment for strength testing with extended electronics for the measurement of the breaking force and flexural tensile strength of the ceramic tiles according to the Standard EN 100 and ISO 10545-4.

Further Information About "ISO10545-4 Strength Testers - Modulus of Rupture (MOR)"

Gabbrielli ceramic test equipment for measuring the Coefficient of Restitution or Impact Resistance according the standard ISO 10545-5 and the determination of the impact resistance according the standard UNI EDL 294 of the ceramic tiles.

Further Information About "ISO10545-5 Coefficient of Restitution Tile Impact Resistance Tester -"

Ceramic Test Equipment for the determination of resistance to thermal shock of the ceramic tiles with water absorption lower than 10%, for tests according to the method with immersion of the ceramics testing Standard ISO 10545-9.

Further Information About "ISO10545-9 Thermal Shock Tank with Immersion"

Ceramic test equipment for the determination of resistance to thermal shock of the ceramic tiles with water absorption higher than 10% according to the method without immersion of the ceramic testing Standard ISO 10545-9.

Further Information About "ISO10545-9 Thermal Shock Tank Without Immersion"

We offer a wide range of General-purpose laboratory ovens, with a temperature range of between 40 — and 600C.

Further Information About "Laboratory Ovens"

A powerful IKA RW20 laboratory stirrer ideally suited to mixing batches of viscous materials. The new RW20 has many technical improvements on the trusted RW 20 series designs This is a tough laboratory work horse that will give years of trouble free working life

Further Information About "Laboratory Stirrers / Mixers"

The Linseis Economy Dilatometer series L76 was developed to be used for CTE measurements in ceramics testing, such as brick and tile industry, porcelain industries and industries manufacturing building materials. It is also widely used for quality control purposes in ceramics and in metal industries. Anderen Ltd are the official UK representatives for Linseis GmbH

Further Information About "Linseis Dilatometer"

The Linseis Horizontal Research Dilatometer series L75H was developed to meet the demands of the research laboratories worldwide including ceramics and steel industry applications. This line of Dilatometers is capable of measurements under vacuum, oxidizing and reducing atmospheres (except 2000°C graphite furnace). This series has built in an automatic pressure control with digital display. Anderen Ltd are the official UK representatives for Linseis GmbH Sample pressure is very important, to accurately measure the CTE values under different pressure conditions.

Further Information About "Linseis L75 Series Dilatometers"

The Linseis Vertical Research Dilatometer series L75V was developed to meet the demands of the research laboratories worldwide including ceramics and steel industry applications. This line of Dilatometers is capable of measurements under vacuum, oxidizing and reducing atmospheres (except 2000°C / 2400°C graphite furnace). This series has a built in automatic pressure control with digital display. Sample pressure is very important, to accurately measure the CTE values under different pressure conditions. A special rate controlled sintering software L75/RCS was developed to measure the Sintering behavior. Sample pressure is very important, to accurately measure the CTE values under different pressure conditions. Anderen Ltd are the official UK representatives for Linseis GmbH

Further Information About "Linseis Vertical Dilatometer"

The ESS Optical Dilatometer offers Dilatometric analysis up to the material’s melting point! Triple the number of tests per day Double accuracy, no calibration nor correction calculations Reduced sample preparation time Supplied in UK through Anderen Ltd Expert Systems Solutions Instruments can be combined to offer an economic solution where multi-parameter testing is required

Further Information About "MISURA Optical Dilatometer"

The ESS DTA is a single investment for differential thermal and thermo-mechanical analyses! • It doubles the number of tests per day! • It saves times in the sample preparation! • Test freedom, with or without crucible! • Possibility of tests on samples taken from the production! Supplied in the UK by Anderen Ltd Expert Systems Solutions Instruments can be combined to offer an economic solution where multi-parameter testing is required

Further Information About "MISURA Differential Thermal Analysis"

The ESS Heating Microscope is a single instrument for softening tests and surface tension! It allows twice the number of tests per day Double accuracy, no calibration nor correction calculations Time saving specimen preparation Expert Systems Solutions are supplied in the UK through Anderen Ltd Expert Systems Solutions Instruments can be combined to offer an economic solution where multi-parameter testing is required

Further Information About "MISURA Heating Microscope"

The Expert Systems Solutions Misura Hot Stage Microscope is a single instrument for softening and surface tension tests Analysis using industrial firing cycles allowing twice the number of tests per day Double accuracy, no calibration nor correction calculations Reduced time in the specimen preparation! Supplied in the UK by Anderen Ltd Expert Systems Solutions Instruments can be combined to offer an economic solution where multi-parameter testing is required

Further Information About "MISURA Hot Stage Microscope"

The Misura Optical Dilatometer manufactured by Expert Systems Solutions offers dilatometric analysis up to the material’s melting point and can triple the number of tests that can be done each day Analysis with industrial thermil cycles, double accuracy, no calibration or correction calculations required Sample preparation time is reduced. Supplied in the UK through Anderen Ltd Expert Systems Solutions Instruments can be combined to offer an economic solution where multi-parameter testing is required

Further Information About "MISURA Optical Dilatometer"

The Expert Systems Solutions Optical Fleximeter is a single instrument for flexural and pyroplasticity tests Allows twice the number of tests per day with double accuracy, no calibration or correction calculations required Supplied in the UK by Anderen Ltd Expert Systems Solutions Instruments can be combined to offer an economic solution where multi-parameter testing is required

Further Information About "MISURA Optical Fleximeter"

The Ohaus Moisture Testing Balance is designed for rapid testing of moisture content in ceramic materials

Further Information About "Ohaus MB45 Moisture Analyser"

Photometer - Palintest 7000 a simple instrument that allows testing of a wide variety of water test requirements for environmental monitoring, either in a laboratory or on site. The instrument does not require highly skilled staff and relies on simple tabletised reagents making testing to high levels of accuracy very simple

Further Information About "Photometer 7500 system"

A pocket microscope fitted with a graticule can be used to measure the thickness of fired glaze in ceramics Unfortunately this is a destructive test - the piece needs to be broken so that a measurement can be made

Further Information About "Pocket Microscope for Glaze Thickness Measurement"

Gabbrielli ceramic testing equipment to measure the Dynamic Coefficient of Friction of flooring surfaces. According the Standards DIN 51130, DIN 51097 and ISO 10545-17 Annex C and the Australian Standard

Further Information About "Ramp Slipperiness Tester to DIN 51130"

The NEW IMPROVED SA-4000+ Scanning Analyser is the worlds only portable meter capable of accurately measuring the level of Lead and Cadmium from ceramics and glass metal release tests. BENEFITS *Simple to use by any competent technician *Lead and Cadmium test done simultaneously using a single use electrode *Requires no special laboratory facilities *Self calibrated *Faster turn around of results compared with outsourcing *Low per test cost *Low capital outlay quick return on investment ANDEREN LTD ARE THE SOLE WORLDWIDE DISTRIBUTOR FOR THE SA4000+ Scanning Analyser

Further Information About "Scanning Analyser for Lead and Cadmium in Ceramics and Glassware Testing"

The Torsion Viscometer (formerly called the Gallenkamp Torsion Viscometer or the Universal Torsion Viscometer) has been used in ceramic testing to measure the viscosity and thixotropy of ceramic slips and glazes all over the world for over 50 years The torsion viscometer is an easy to use and easy to maintain instrument that offers repeatable results with low operator skill and will have a long working life

Further Information About "Torsion Viscometer (Universal or Gallenkamp type) for ceramic testing"

The new Tortus 3 Coefficient of Friction Tester is the most advanced version of the original BCRA designed instrument, using the latest technology available on the market today and is a replacement for the Tortus II The battery operated instrument can be used to test the resistance to skidding of a wide variety of flooring surfaces including ceramic tiles in both dry and wet conditions. Results can be presented on the integral chart recorder but also down loaded to a PC via a USB connection. The benefit of this is that the unit does no require and connecting cables either to a mains supply or to a PC making it completely portable

Further Information About "Tortus 3 Coefficient of Friction Tester"

Roughness measurements can be useful to quickly identify locations where differences of wet slip resistance may exist. It can also be used to measure directional differences that might also crate a slip hazard. In addition the TR100 Surface Roughness Meter can identify changes in surfaces due to wear over time and soiling caused by traffic. Roughness measurement should be included as part of the ISO10545 test for Coefficient of Friction and an integral part of any in-situ measurements

Further Information About "TR100 Surface Roughness Meter"

Roughness measurements can be useful to quickly identify locations where differences of wet slip resistance may exist. It can also be used to measure directional differences that might also crate a slip hazard. In addition the TR210 Surface Roughness Meter can identify changes in surfaces due to wear over time and soiling caused by traffic. Roughness measurement should be included as part of the ISO10545 test for Coefficient of Friction and an integral part of any in-situ measurements

Further Information About "TR210 Surface Roughness Meter"

Quality control, standards compliance, increase yields. From raw materials to finished product – we work with you for the best results.

Producing ceramics is a multi-stage process. Control throughout this process reduces faults and improves yields. Finished product needs testing to confirm it meets international standards.

All ceramic testing needs to be accurate and repeatable, you need the best equipment available.

With over 30 years experience supplying testing solutions worldwide, we have the products and the understanding of the requirements of international ceramic test standards, raw material testing and in process control.

Do you need a turn key project with product and application training, we are your one stop shop Our product range includes equipment for sanitaryware, tableware, tiles, high tech ceramics, and raw material testing.